Dome CXtra User's Guide

Dome EX DisplayMX2/MX3 Display ControllerUSER’S GUIDE

AMLCD panel mounted on desk standDisplay controllerDVI cablesDC power adapter Power cordsDisplay driver andcalibration softwareQuick reference

About the Display The Dome EX display system is designed for medical imaging in diagnostic settings, in portrait or landscape orientation, and comes f

2 | Dome EX DisplayDisplay ComponentsReview this illustration of the back panel to identify controls and ports on the display unit.Legend1 Reset b

About the Display | 3Display PositionsYou can adjust the tilt, height, viewing angle, and orientation of the display to maintain an ergonomic and

4 | Dome EX DisplayDesk Stand FeaturesUnfasten the stand lock to adjust display height. Remove the stand cover to thread the power cord and DVI ca

Installing the Display | 5Installing the DisplayBefore you install the display controller, remove any existing graphics card and its driver from y

6 | Dome EX DisplayInstall Display ControllerBefore you install the display controller, make sure your display system is set up in a well-ventilat

Installing the Display | 7Connect the Video and Power CablesLeave your computer off. Make sure the power cord is plugged into the grounded outlet.

8 | Dome EX DisplayInstall Display DriverLog on with administrator privileges to install the display driver. NOTE: This driver requires the Window

Installing the Display | 9To configure the display1 Right-click the desktop and select Properties > Settings.2 Use the native resolution of the

© 2006 Planar Systems, Inc. All rights reserved.Information in this document has been carefully checked for accuracy; however, no guarantee is given t

10 | Dome EX DisplayTo change video setting per display1 Click the PowerDesk icon on the taskbar.2 On the PowerDesk menu, select the graphics card

Installing the Display | 11Install Dome CXtraBundled with the display system, the Dome CXtra software enhances the functionality of the Dome E2 an

12 | Dome EX DisplayAppendixTroubleshootingDome E2 SpecificationDome E3 SpecificationVideo ModesConnector PortsLED Status LightsComponent RemovalP

Troubleshooting | 13TroubleshootingProblem Possible Cause SolutionNo information after installation of video adapter boardBoard not properly insta

14 | Dome EX DisplayDome E2 SpecificationIn locations where 240V outlets are used, connect the Dome E2 display to only a center-tapped, 240V, sing

Dome E2 Specification | 15Power SupplyCAUTION: Use only the power adapter supplied with the Dome E2 display unit; Ault MW116KA1249F53. Reliabilit

16 | Dome EX DisplayDome E3 SpecificationIn locations where 240V outlets are used, connect the Dome E3 display to only a center-tapped, 240V, sing

Dome E3 Specification | 17Power SupplyCAUTION: Use only the power adapter supplied with the Dome E3 display unit; Ault MW122RA1223F52. Reliability

18 | Dome EX DisplayVideo ModesResolutions expressed in pixels (W x H). Display Resolution Orientation Bits per pixelDome E2 1200 x 16001600 x

Connector Ports | 19Connector PortsThe video signal connector is a standard DVI connector. The Dome E2 display uses a 4-pin DIN connector. The pow

iiiContentsProduct Information ivAbout the Display 1Installing the Display 5Appendix 12Index 23Regulatory Compliance 25S

20 | Dome EX DisplayLED Status LightsThe two LEDs on the back panel provide information about the display.• LED A describes the digital-link statu

LED Status Lights | 21Power-up sequence information from LEDLED A status information after initial power-onLED B status information after initial

22 | Dome EX DisplayDisplay Driver RemovalFollow the appropriate procedure below to remove the MX driver from your system, or use the Add/Remove P

23IndexBbrightness, display 9Ccleaning viiiconfiguring display 9connectingDVI cable 7power cord 7connector port 19contents, package xDdesk stand 4DIN

Ssafety precautions visetting brightness 9setting multi-mode 9, 10setting rotation 9shipping/storing ixspecificationDome E2 display 14Dome E3 display

Regulatory ComplianceCanada, European Union, United StatesThis display has been tested and found to comply with IEC/EN 60601-1 and IEC/EN 60601-1-2 st

The applicable safety standards for an MDD Class I display are IEC/EN 60601-1:1990 along with Amendments 1 and 2. To help the medical device designer

EU Declaration of Conformity for Medical ApplicationA Declaration of Conformity has been filed for this product. For additional copies of the Declarat

U.S. FCC Compliance StatementDisplay Unit This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)

AustralianChina JapanKoreaC-Tick Australian Communications Authority regulating product EMC compliance. CCC China Compulsory Certification regulating

iv | Dome EX DisplayProduct InformationThe design of the Dome EX digital display takes into account every known measure to ensure your personal sa

Standard WarrantySummary• Standard 1-year “repair and return” warranty• Industry-leading 10-year backlight warranty on grayscale displays*• Typical re

3 Warranty is void on any product with damage, deterioration, or malfunction resulting from the following:a) Accident, misuse, neglect, fire, water, l

America SalesPlanar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA (503) 748-1100 phone(503) 748-1493 faxMedical SalesPlanar Systems

Product Information | vSymbol explanationsIntended useThe Dome EX display is an AMLCD display designed for viewing medical X-ray images. This unit

vi | Dome EX DisplaySafety precautionsExternal equipment intended for connection to signal input, signal output, or other connectors, must comply

Product Information | viiUnpacking and handling tipsThe Dome EX display is a precision instrument that requires proper care to maintain product oper

viii | Dome EX DisplayPreventing fire and injury• Replace the power supply or cables if damaged.• Use only the power source indicated in this guid

Product Information | ixShipping/storing the displayKeep the display in its shipping container until installation. Return the display to its origina